Patent application number | Description | Published |
20100160400 | TREATMENT USING DANTROLENE - Provided are low-volume, safe for injection formulations of dantrolene yielding significant advantages over the currently approved and marketed dantrolene for malignant hyperthermia (MH) threatening anesthetic crisis. Once dantrolene can be made immediately available to patients triggered of MH, the anesthesiologist will be able to focus exclusively on the management of the patient's physiologic status in this complex and evolving crisis, not on the laborious and time consuming reconstitution process of the rescue agent. The low volume, safe for injection formulations of dantrolene have significant advantages over currently used approaches to the prevention and treatment of pumphead, and other neurological, cognitive and motor dysfunction incident to iatrogenically or trauma induced situations of altered blood flow, including those incurred during surgical procedures involving CPB or related procedures, as well as those incurred during non-normothermic episodes caused iatrogenically or by disease. | 06-24-2010 |
20120121662 | TREATMENT USING DANTROLENE - Provided are low-volume, safe for injection formulations of dantrolene yielding significant advantages over the currently approved and marketed dantrolene for malignant hyperthermia (MH) threatening anesthetic crisis. Once dantrolene can be made immediately available to patients triggered of MH, the anesthesiologist will be able to focus exclusively on the management of the patient's physiologic status in this complex and evolving crisis, not on the laborious and time consuming reconstitution process of the rescue agent. The low volume, safe for injection formulations of dantrolene have significant advantages over currently used approaches to the prevention and treatment of pumphead, and other neurological, cognitive and motor dysfunction incident to iatrogenically or trauma induced situations of altered blood flow, including those incurred during surgical procedures involving CPB or related procedures, as well as those incurred during non-normothermic episodes caused iatrogenically or by disease. | 05-17-2012 |
20120121663 | TREATMENT USING DANTROLENE - Provided are low-volume, safe for injection formulations of dantrolene yielding significant advantages over the currently approved and marketed dantrolene for malignant hyperthermia (MH) threatening anesthetic crisis. Once dantrolene can be made immediately available to patients triggered of MH, the anesthesiologist will be able to focus exclusively on the management of the patient's physiologic status in this complex and evolving crisis, not on the laborious and time consuming reconstitution process of the rescue agent. The low volume, safe for injection formulations of dantrolene have significant advantages over currently used approaches to the prevention and treatment of pumphead, and other neurological, cognitive and motor dysfunction incident to iatrogenically or trauma induced situations of altered blood flow, including those incurred during surgical procedures involving CPB or related procedures, as well as those incurred during non-normothermic episodes caused iatrogenically or by disease. | 05-17-2012 |
20140099382 | TREATMENT USING DANTROLENE - Provided are low-volume, safe for injection formulations of dantrolene yielding significant advantages over the currently approved and marketed dantrolene for malignant hyperthermia (MH) threatening anesthetic crisis. Once dantrolene can be made immediately available to patients triggered of MH, the anesthesiologist will be able to focus exclusively on the management of the patient's physiologic status in this complex and evolving crisis, not on the laborious and time consuming reconstitution process of the rescue agent. The low volume, safe for injection formulations of dantrolene have significant advantages over currently used approaches to the prevention and treatment of pumphead, and other neurological, cognitive and motor dysfunction incident to iatrogenically or trauma induced situations of altered blood flow, including those incurred during surgical procedures involving CPB or related procedures, as well as those incurred during non-normothermic episodes caused iatrogenically or by disease. | 04-10-2014 |
20140105989 | Treatment Methods with Low-Dose, Longer-Acting Formulations of Local Anesthetics and Other Agents - Drug formulations that provide sustained action and/or reduced dosage requirements are provided. In the formulations the drugs (particularly local anesthetics) are associated with reversed cubic phase and reversed hexagonal phase lyotropic liquid crystalline material. | 04-17-2014 |
20160074366 | TREATMENT USING DANTROLENE - Provided are low-volume, safe for injection formulations of dantrolene yielding significant advantages over the currently approved and marketed dantrolene for malignant hyperthermia (MH) threatening anesthetic crisis. Once dantrolene can be made immediately available to patients triggered of MH, the anesthesiologist will be able to focus exclusively on the management of the patient's physiologic status in this complex and evolving crisis, not on the laborious and time consuming reconstitution process of the rescue agent. The low volume, safe for injection formulations of dantrolene have significant advantages over currently used approaches to the prevention and treatment of pumphead, and other neurological, cognitive and motor dysfunction incident to iatrogenically or trauma induced situations of altered blood flow, including those incurred during surgical procedures involving CPB or related procedures, as well as those incurred during non-normothermic episodes caused iatrogenically or by disease. | 03-17-2016 |
Patent application number | Description | Published |
20120185058 | METHOD AND INSTRUMENTATION FOR ACETABULAR LABRUM RECONSTRUCTION - Methods and instruments for repairing a damaged acetabular labrum. The arc length of a portion of an acetabular rim proximal to the damaged (torn or broken) region of the acetabular labrum is measured, and a graft, such as a meniscal allograft or a gracilis autograft, is trimmed according to the measurement and secured in the damaged region of the acetabular labrum as a replacement. Various instruments, such as a wheel mounted on an arm, a measuring member with spaced tines, or a hollow arm with a graduated wire, can be used to measure the arc length of the damaged region of the acetabular labrum. | 07-19-2012 |
20130345749 | KNOTLESS SUTURE ANCHORS AND METHODS OF TISSUE REPAIR - Systems and methods for soft tissue to bone repairs employing tensionable knotless anchors, without knot tying. The tensionable knotless anchors may be used by themselves or in combination with additional constructs (which may have a similar or different configuration, i.e., modified according to the specific repair) and with the flexible strands provided through tissue, around tissue, or through and around tissue to be repaired or fixated. The tensionable knotless anchors may be used to achieve simple stitch repairs, mattress stitch repairs or interlocked looped mattress repairs, among others. The tensionable knotless anchors may be also provided in a daisy chain configuration, i.e., with the suture from one anchor passed through the eyelet/loop of the shuttle/pull device of another anchor and repeated in a pattern. | 12-26-2013 |
Patent application number | Description | Published |
20090194067 | SERVICE PACK POWER MANAGEMENT - A power management system, in certain aspects, may utilize direct load sensing feedback from the prime mover (e.g., engine), thereby reducing the possibility of overloading the prime mover. The use of direct load sense feedback from the prime mover can then be used with additional feedback, such as prime mover RPM feedback and individual output load sensing feedback, to directly control the output loads and set the primary power sources rpm set-point to better manage the power available and reduce the possibility of overloading the primary power source. | 08-06-2009 |
20100199753 | FUEL USAGE MONITORING SYSTEM FOR A SERVICE PACK - A fuel usage monitoring system, in certain aspects, may be configured to determine the fuel usage rate of a work vehicle service pack engine using control signals relating to operating parameters of the service pack engine and associated equipment. In certain embodiments, the control signals may relate to operating parameters of the engine, a fuel injection pump associated with the engine, a governor associated with the fuel injection pump, a fuel reservoir associated with the engine, and other components associated with the engine. In particular, the control signals may relate a position of a control rack of the fuel injection pump. The control signals may be correlated with fuel usage rates prior to operation of the fuel usage monitoring system. In addition, the correlations may vary as certain parameters of the engine, such as operating speed, vary. The correlations may be implemented as algorithms within software of the fuel usage monitoring system. | 08-12-2010 |
20150273607 | SYSTEMS AND METHODS FOR WIRELESS CONTROL OF AN ENGINE-DRIVEN WELDING POWER SUPPLY - Embodiments described herein include wireless control of a welding power supply via portable electronic devices. In particular, operating parameters and statuses of the welding power supply may be modified by the portable electronic device, as well as be displayed on the portable electronic device. For example, in certain embodiments, the welding power supply may be an engine-driven welding power supply, and the portable electronic device may be configured to start and/or stop an engine of the engine-driven welding power supply. A pairing procedure may be used to pair the welding power supply and the portable electronic device in a wireless communication network. Furthermore, in certain embodiments, a method of prioritization of control between a control panel of the welding power supply and the portable electronic device may be implemented. | 10-01-2015 |
20150273609 | SYSTEMS AND METHODS FOR PRIORITIZATION OF WIRELESS CONTROL OF A WELDING POWER SUPPLY - Embodiments described herein include wireless control of a welding power supply via portable electronic devices. In particular, operating parameters and statuses of the welding power supply may be modified by the portable electronic device, as well as be displayed on the portable electronic device. For example, in certain embodiments, the welding power supply may be an engine-driven welding power supply, and the portable electronic device may be configured to start and/or stop an engine of the engine-driven welding power supply. A pairing procedure may be used to pair the welding power supply and the portable electronic device in a wireless communication network. Furthermore, in certain embodiments, a method of prioritization of control between a control panel of the welding power supply and the portable electronic device may be implemented. | 10-01-2015 |
20150273610 | SYSTEMS AND METHODS FOR PAIRING OF WIRELESS CONTROL DEVICES WITH A WELDING POWER SUPPLY - Embodiments described herein include wireless control of a welding power supply via portable electronic devices. In particular, operating parameters and statuses of the welding power supply may be modified by the portable electronic device, as well as be displayed on the portable electronic device. For example, in certain embodiments, the welding power supply may be an engine-driven welding power supply, and the portable electronic device may be configured to start and/or stop an engine of the engine-driven welding power supply. A pairing procedure may be used to pair the welding power supply and the portable electronic device in a wireless communication network. Furthermore, in certain embodiments, a method of prioritization of control between a control panel of the welding power supply and the portable electronic device may be implemented. | 10-01-2015 |
20150273611 | SYSTEMS AND METHODS FOR WIRELESS CONTROL OF A WELDING POWER SUPPLY - Embodiments described herein include wireless control of a welding power supply via portable electronic devices. In particular, operating parameters and statuses of the welding power supply may be modified by the portable electronic device, as well as be displayed on the portable electronic device. For example, in certain embodiments, the welding power supply may be an engine-driven welding power supply, and the portable electronic device may be configured to start and/or stop an engine of the engine-driven welding power supply. A pairing procedure may be used to pair the welding power supply and the portable electronic device in a wireless communication network. Furthermore, in certain embodiments, a method of prioritization of control between a control panel of the welding power supply and the portable electronic device may be implemented. | 10-01-2015 |